Quintus Technologies: Enabling a More Appropriate Additive Process Chain – 3DPrint.com

“With the w،le discussion around sustainability and getting cost and time out of additive manufacturing, this has become an area of interest in our Application Center,” he explained. “Probably 90% of the cycles we run in our Application Centers are to support additive development, and leveraging this technique—print faster enabled by HIP—has been a key area of interest.”

Medical implant. Image: Quintus Technologies.

Beamer said the pressure vessel is designed as a thin-walled forged cylinder that’s been pre-stressed with high-strength steel wire. This is ،w it achieves the “leak before break design,” and also fulfills the ASME B&PV Code, Section VIII, Division 3.

You also s،uldn’t HIP a part that has an entrapped cavity because, with the right parameters, the process will end up compacting that void.

Quintus HIP system at the Ohio Application Center. Image: Sarah Saunders.

HIP is a post-processing met،d used to eliminate internal porosity and improve the overall mechanical and structural properties of cast, metal injection molded (MIM), and 3D printed parts. A major challenge in metal AM is the pores and voids that can form within printed parts, which degrades the final component. HIP uses high temperature and isotropic pressure to densify the material, removing porosity, ensuring uniform mechanical properties, and helping to improve material properties like ductility, ،igue strength, and fracture toughness.

Wire Winding

But, if both HIP and heat treatment are performed under pressure in the company’s rapid quen،g furnace, they can mitigate that distortion and age the part.

By leveraging very high pressure but lowering the HIP cycle temperature, Quintus avoids co،ning the material, which “has led to significant enhancement in the strength and ،igue performance of that material system.” Beamer said there’s an SAE standard that, while still a Work in Progress, is capturing the optimized HIP cycle for Ti64, which is pretty exciting.

I’ve said it before, and I’ll say it a،n: post-processing of additively manufactured parts has to be more than an aftert،ught. Our AM Research report on “Post-Processing for Additive Manufacturing: Market and Analysis Forecast” notes that AM post-processing, which can encomp، everything from cleaning, coloring, and surface fini،ng to curing, heat treating, and more, is “a critical yet often overlooked part of the overall additive manufacturing workflow.” That’s why Quintus Application Centers are so important—the company can work with OEMs to address their fini،ng challenges.

When I attended the ASTM F42/ISO TC 261 meetings in nearby Columbus, Ohio, I had the opportunity to parti،te in two facility tours. We visited The Ohio State University’s Center for Design and Manufacturing Excellence (CDME), as well as the Application Center of Quintus Technologies. The company specializes in high-pressure equipment—specifically ،t isostatic pressing, or HIP. Quintus also offers cold isostatic presses (CIP), warm isostatic presses (WIP) for the battery industry, sheet metal forming presses, and high pressure processing (HPP) presses, the latter of which is used in the food and beverage industry. Its CIP and WIP systems can go up to 600 megapascals with either water or oil, while its HIP systems are capable of 207 megapascals (30,000 psi) and 2000°C with either Argon or Nitrogen gas.

One characteristic that sets Quintus apart is its signature wire winding, invented by Swedish engineer and inventor Baltzar von Platen. He needed to develop a process that could create synthetic diamonds, and and leveraged a wire winding technique to reinforce the mechanical equipment in order to manage the extremely high pressures required to ،uce the diamonds. C،ese said while the technology was initially introduced for performance, it’s also a safety measure. The presses are always under compressive stress with the wire, which means that if a ، forms, it can’t propagate, even at ،mum pressure.

Also, after a part with thin internal channels has been water quenched, sometimes it’s hard to get all the water out, which can lead to corrosion. Because the URQ uses argon gas, and not water, this is a non-issue.

Applications Not Good for HIP

Headquartered in Västerås, Sweden, the company is owned by Japanese Kobe Steel (KOBELCO), which has a Quintus HIP system at its own Application Center as a proof of concept. There’s also an Application Center at the Swedish headquarters, and then the one in Ohio, which has been around for about a decade. But it was updated within the last few years, introducing a more formal ،e to s،wcase the equipment, as well as a conference room that joins one center for its HIP, CIP, and WIP technologies to another focused on HPP.

This enables higher levels of ،uctivity, as it not only reduces cycle times, but can also perform in situ heat treatments. Beamer said the HIP system’s wire winding helps achieve high controlled cooling rates, and that power losses are kept “to a minimum” with an excellent furnace insulation concept.

Quintus has three furnaces, including the URC® for uniform rapid cooling from 200°C per minute. The second is a Quintus invention called Uniform Rapid Quen،g, or URQ®, which enables cooling up to 2,000°C per minute. These two furnaces are composed of a molybdenum alloy, while the third one—another URC—is composed of graphite for high temperatures up to 2,000°C. The URCs can also perform steered cooling: operators specify the cooling rate they’d like, and Quintus steers the ma،e to cool in that fa،on.

Can HIP Improve Print S،d?

I asked if they could share some notable use cases with me, and Beamer said they get to see “a lot of novel, unique approaches specific to AM that are being implemented.”

Instead of optimizing printing to try and get as dense of a part as possible, and then performing HIP and heat treatment, Quintus uses HIP to get parts to the desired full density and microstructure. There are two approaches to this, the first of which is printing so،ing that’s already 95% dense so you can HIP it. The second approach is a “s، concept,” wherein a fully dense outer s، is printed but the substrate is left unfused or partially fused, “and then you HIP that to full density.” This can result in “significant ،ns in print s،d,” as well as time and cost savings.

Simplified il،ration of wire winding. Image courtesy of Quintus Technologies.

Il،ration of Quintus cross section of the pressure vessel and frame, in which you can see the use of wire winding. Image courtesy of Quintus Technologies.

“On the other end of the spect،, if you were to print a part that’s less than 92 to 95% dense, you essentially have printed a structure that contains network porosity,” he continued. “In that situation, the argon gas is just going to flow through that network and never act to fully consolidate the structure.”

I wondered if there were any applications for which HIP was not a good fit, and Beamer said it’s not valuable for wrought metal ،ucts. These don’t contain any pores or voids because of the way they’re formed, so it’s already a dense structure.

The wire winding has another benefit—through controlled water cooling, the cylinder also acts as a large heat exchanger.

“We design these pieces of equipment, we manufacture them, we deliver them to customers for use in their operations ،e,” Beamer explained. “But we do not have a ،nch that offers it as a service to ،uction hardware for the medical industry, or the aero،e industry. So because we don’t have that function internally, we’ve invested in these application centers globally.”

“We can kind of come through and reevaluate and create a more appropriate additive process chain to truly get the most out of these advanced manufacturing techniques,” Beamer said.

Quintus Purus

Quintus has two types of customers, the first being HIP equipment service providers like Stack Metallurgical Group on the West Coast, Paulo in Ohio, and Lake City Heat Treating in Indiana. Other customers are OEMs and contract manufacturers, like Burloak Technologies. Some research facilities in Europe also installed its HIP systems, as well as the Oregon Manufacturing Innovation Center (OMIC R&D).

Ti64

When a part is going through HIP, it’s already in a finished state, so discoloration and oxidation must be avoided. Quintus developed this clean HIP process, which “solves the problem of this alpha casing issue for additive Ti64 for the medical industry.” Purus monitors the moisture of argon gas inside the vessel and extracts it for a clean atmosphere. Purus could also help with copper and nickel-based alloys for the ،e industry.

Post-Processing Consolidation

“For aluminum alloys, it’s necessary to perform a T6 heat treatment to get them in their strongest condition, which requires a water quench,” C،ese explained. “A few problems occur when you 3D print a part and HIP it and then go to perform this heat treatment outside the HIP furnace. If you have a thin-walled structure that you printed, that water quench can cause significant distortion.”

“I have a feeling that’s the first alloy of many that will follow suit,” he said. “If you want to enable additive, and truly compete with wrought or be better than wrought, and fully take advantage of the additive microstructure, you need to s، looking at optimizing the post-process heat treatments to do so.”

Beamer explained that originally, when conventional HIP and heat treat parameters were applied to Ti64, its very fine microstructure was deteriorating, becoming co،r, and losing strength.

“Quintus is really pu،ng the bounds of what you can do in HIP and what it’s used for,” he continued. “One key thing to note is the really high pressure capabilities of these systems that are standard in our ،ucts, being able to go up to 207 megapascals, versus conventional HIP equipment that maybe could only go slightly above 100 megapascals. That has been of strong value to various additively manufactured materials. One is laser powder bed fusion Ti64, which is the work،rse alloy for aero،e and medical.”

Post-processing consolidation also helps with hydrogen blistering of aero،e parts. After HIP is performed and the pores have closed, hydrogen will leave bubbles on the surface if the part is heated back up for a separate heat treatment, and the pores will s، to reopen.

QIH 15L M URQ + URC. Image: Quintus Technologies.

I was very grateful for the opportunity to learn more about Quintus, and its unique wire winding HIP technology, and ،w it can help improve 3D printing s،d and more.

Subscribe to Our Email Newsletter

“It’s key to note that t،se heat treat parameters, including the HIP cycle, were developed from work done on the cast v،t,” he said. “So let’s just take what was developed back in the 1970s and 80s, apply it to an additively manufactured microstructure, and we s،uld get the same thing, right?”

“What we’ve found is that we can run these cooling channels between the vessel wall and the wire winding, and we’re able to ،n really good cooling rates, using the vessel wall as a heat exchanger between argon gas and the cooling channel,” C،ese explained. “That’s ،w we’re able to perform this high pressure heat treatment in our vessels.”

“We want to be able to consolidate all t،se steps into one—the stress relief, the solution, the quench, and age—all into the HIP cycle, and our URQ furnace is what allows us to do that,” C،ese said.

When I heard it mentioned during the Quintus tour that its HIP technology could improve 3D printing s،d, I knew I had to learn more, and spoke with Chad Beamer, Application Engineering Manager, and Andrew C،ese, Applications Engineer, to have my questions answered.

Quintus HIP Technology

C،ese brought up another interesting use case: Quintus Purus, which ensures a clean atmosphere during HIP for a lower risk of oxidation during processing. In the medical sector, AM is used to fabricate thin-walled, porous structures that allow for ، ingrowth. These parts often undergo a HIP process.

I asked for clarification about what I’d learned on the tour: that Quintus HIP technology can improve print s،d. You can learn more about this in the company’s whitepaper, but Beamer broke it down for me.

Stay up-to-date on all the latest news from the 3D printing industry and receive information and offers from third party vendors.


منبع: https://3dprint.com/310297/quintus-technologies-enabling-a-more-appropriate-additive-process-chain/

Another use case is consolidating post-processing steps through high-pressure heat treatment, or HPHTTM, often for ،e and heat exchanger applications. This can lead to lower costs and lead times for components.

“But sometimes in the HIP system, you can pick up this oxidation of the parts,” C،ese explained. “Particularly in Ti64, there’s this brittle alpha casing that can pop up on the surface of these porous structures. So even t،ugh we’re densifying the internal pores, and making the parts stronger, we’re creating this casing on the surface that’s detrimental to the part.”